![]() Repeat this process three or four more times. Then you’re going to want to unplug your computer from the charger and drain it down to single digits again. Essentially what you want to do is drain the battery down to single digits and then let it charge for 12 hours or until it’s at 100%. I highly recommend going through a few conditioning cycles for your new battery. Battery Conditioning and Calibration for a MacBook Pro Also, if you had the “Replace Soon” warning, that should be gone, and the Battery Condition should be set to Normal. This is what you want to see because it shows that the system recognizes that it has a brand new battery. My computer shows the new EGOWAY battery with a Cycle Count of 1. You can run a System Report by going to Apple > About This Mac > System Report. Give it some time to boot up, and then check the battery percentage. If everything goes well, you’ll see the main boot screen. Once you’re finished, flip the computer back upright and press the power button. Connect the cover using the screws that you aligned from Step 1. The goal is to make sure the seams are flush and everything is aligned nicely. Grab the back cover and align it over the computer. Lastly, reattach the battery connector to the mainboard, and then close up the case. You can also perform a final tightening to be sure the battery is secure. I recommend going between both screws and make sure that you have everything lined up. ![]() Line up the battery, and replace the battery screws. We’ll connect it after we’re done working inside of the case. You’ll want to make sure that you give yourself enough space on the connector side so that you’re not squeezing the cord down. Then, take the new battery and slide it into place. Wiggle it out of the case, and place it to the side. Use the flaps on the battery and the spudger tool to peel out the old battery. Don’t mix them up, because we’ll be reusing these for the new battery. The first screw on the left is smaller, and the second screw on the right is longer. Once you have the screwdriver, loosen up the two screws on either side of the battery. Standard tools don’t work for these screws (I’ve tried), so ensure that your battery comes with one of these tools. Next, grab the three-prong screwdriver that came with your battery. Take extra caution not to hit any surrounding components. You just want to loosen up the connector so that you can take it apart with your fingers. To do this, grab one of your spudger tools, and gently rock it back and forth around the battery connector. Now that we’re inside the Mac, disconnect the battery. Related: While you have the cover off, you may want to upgrade the RAM and add an SSD. Let’s go through each of these steps in more detail. Take out the old battery and put in a new one.We can perform the upgrade in just three steps. If you’re fortunate to have an older 2012 MacBook Pro, the battery replacement is very easy, and super straightforward. Unfortunately, most standard household screwdrivers do not fit the MacBook Pro screws, so you’re going to need a set of these if you’re planning on opening up your Mac. All you need is a Torx screwdriver kit and a spudger. You don’t need a lot of tools to perform a battery upgrade on a MacBook Pro. Tools to Upgrade a Mid-2012 MacBook Pro Battery I also had next-day shipping through Amazon Prime, which was convenient. It has good reviews, and it cost me about $40. I ended up picking the EGOWAY laptop battery for the MacBook Pro. Most battery screws are different than a standard flat or Phillips’s head, so the screwdriver kit will come in handy when you go to swap out the old battery. Don’t go super cheap on this, because after all, it is a battery, and it’s important to have cells that are quality.īe sure to find a battery that comes with a screwdriver set. I highly recommend choosing a middle-price battery. What I like to do is read through the reviews and figure out which battery has the best ratings. You’ll want to find an A1322 battery cell that is designed to fit the mid-2012 MacBook Pro. I used Amazon to purchase my replacement battery, but you can use whatever online reseller you like ( OWC, iFixit, etc.). ![]() How to Find the Right MacBook Pro Replacement Battery However, if opening your Mac makes you squeamish, you may want to hire someone to perform the upgrade instead. If you’re comfortable using a screwdriver and have a bit of patience, I’d say go for the repair yourself. All you need to do is go on Amazon (or find a reseller for aftermarket batteries), purchase an A1322 battery, and spend 10 to 30 minutes installing it. This repair project is very straightforward. Note: At the time of this post, I’ve only had the new battery for a few days, so I’ll keep you updated on how this battery is performing over the next few months.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |